preliminary specification ? andigilog, inc. 2004 www.andigilog.com february 2004 ? 70a04013_001 aam3202 / AAM3203 u ltra l ow p ower , d ual -spdt cmos a nalog s witches p roduct s pecification preliminary specification - subject to change without notice preliminary specification - subject to change without notice general description the aam3202 and AAM3203 are precision cmos analog dual-spdt switches or 2:1 multiplexers offering low on-resistance of less than 4 ? , with better than 0.4 ? matching between channels and on-resistance flatness of less than 1.2 ? over the specified analog input voltage range. the aam3202 and AAM3203 have very fast turn- on switching speed of less than 16ns over the full operating temperature range of -40c to 85c. the aam3202 and AAM3203 also consume a minimal amount of power, making them ideal for portable equipment. the aam3202 and AAM3203 connect 1-of-2 inputs to a common output by control of a select pin in a dual configuration. the aam3202 has an inverted switch logic compared to the AAM3203. the parts are available in a 10-contact leadless qfn package and operate over the range from 1.8v to 5.5v. features (at 5v v dd ) ? low on-resistance: 4 ? max ? guaranteed on-resistance match between channels, < 0.4 ? ? guaranteed flat on-resis tance over specified signal range, < 1.2 ?. ? turn-on time: 12ns at 25c ? turn-off time: 5ns at 25c ? break before make interval: 7ns typ ? temperature range: -40c to 85c ? uses a single supply, 3v to 5v nominal applications ? mobile communications ? computers and peripherals ? battery management ? fax machines/printers/copiers ? portable medical instruments pin configuration functional diagrams ordering information part number package temperature range part marking how supplied aam3202q10 10-lead qfn -40 ?c to +85 ? c aam3202 3000 units on t&r AAM3203q10 10-lead qfn -40 ?c to +85 ? c AAM3203 3000 units on t&r aam3202 in1 no1 gnd no2 in2 com1 nc1 nc2 com2 AAM3203 in1 nc1 gnd nc2 in2 com1 no1 no2 com2 v dd v dd aam3202 in1 no1 gnd no2 in2 com1 nc1 nc2 com2 AAM3203 in1 nc1 gnd nc2 in2 com1 no1 no2 com2 v dd v dd com1 in1 no1 nc1 no2 com2 v dd gnd nc2 in2 in1 com1 nc1 no1 nc2 com2 v dd gnd no2 in2 1 aam3202 2 3 4 5 10 9 8 7 6 1 AAM3203 2 3 4 5 10 9 8 7 6 com1 in1 no1 nc1 no2 com2 v dd gnd nc2 in2 in1 com1 nc1 no1 nc2 com2 v dd gnd no2 in2 1 aam3202 2 3 4 5 10 9 8 7 6 1 AAM3203 2 3 4 5 10 9 8 7 6
aam3202 / AAM3203 - 2 - ? andigilog, inc. 2004 www.andigilog.com april 2004 ? 70a04011 absolute maximum ratings 1 n otes : 1. absolute maximum ratings are limits beyond which operation may cause permanent damage to the device. these are stress ratings only; functional operations at or above these limits is not implied. preliminary specification - subject to change without notice preliminary specification - subject to change without notice 2. human body model: 100pf capacitor discharged through a 1.5k resistor into each pin. machine model: 200pf capacitor discharged directly into each pin. 3. these specifications are guaranteed only for the test conditions listed. recommended operating ratings symbol parameter min max units v dd supply voltage +1.8 +6 v v no , v nc, v com analog signal level 0 v dd v t a operating temperature range -40 +85 c dc electrical characteristics (digital section) 3 limits apply for - 40c t a +85c and v dd = + 5.0v unless otherwise noted. parameter symbol conditions min max units min hi-level input voltage v ih -40c t a +85c v dd =+2.7v v dd =+4.5v 2.0v 2.4v v max low-level input voltage v il -40c t a +85c v dd =+2.7v v dd =+4.5v 0.4v 0.8v v digital input leakage i in v add & v en = 0v or +5.5v v dd = +5.5v t a =+25c t a =-40c to+85c -0.1 -1.0 0.1 1.0 a digital input power off leakage i off v add & v en = 0v or +5.5v v dd = 0v t a =+25c t a =-40c to+85c -0.1 -1.0 0.1 1.0 a dc electrical characteristics (analog section) 3 limits apply for - 40c t a +85c and v dd = + 5.0v unless otherwise noted. parameter symbol conditions min typ max units i no = -10ma v com = 0v to +5v t a =+25c t a =-40c to+85c 2 4 ? on-resistance r on i no = -10ma v com = 0v to +3v t a =+25c t a =-40c to+85c 4 7 ? i no = -10 m a , v dd =+4.5v v com = 0 to v dd t a =+25c t a =-40c to+85c 0.1 0.4 ? on-resistance channel matching ? r on i no = -10 m a , v dd =+2.7v v com = 0 to v dd t a =+25c t a =-40c to+85c 0.1 0.4 ? i no = -10ma, v dd =+5v v com = +1v, +2.5v, +4v t a =+25c t a =-40c to+85c 0.5 1.2 ? on-resistance flatness r flat i no = -10ma, v dd =3v v com = +.6v, +1.5v, +2.4v t a =+25c t a =-40c to+85c 1.5 2.5 ? supply current i dd v dd =+3.3v or +5.5v, v add & v en = 0v t a =+25c t a =-40c to+85c 0.1 1 a parameter rating supply voltage +7v analog input/output voltage -0.5v to v dd + 0.5v in1/in2 input voltage -0.5v to +7v continuous current, any terminal 50ma storage temperature range -60 c to +150 c lead soldering temperature 260 c human body model 2000v esd 2 machine model 250v thermal resistance - ja tbd lead temperature 260 c
aam3202 / AAM3203 - 3 - ? andigilog, inc. 2004 www.andigilog.com april 2004 ? 70a04011 dynamic electrical characteristics 3 limits apply for - 40c t a +85c and v dd = + 5.0v unless otherwise noted. parameter symbol conditions min typ max units v dd = +5v, v no = 3v c l =35pf, r l =300 ? t a =+25c t a =-40c to+85c 12 16 ns turn-on time t on(en) v dd = +3v, v no = 2v c l =35pf, r l =300 ? t a =+25c t a =-40c to+85c 14 20 ns v dd = +5v, v no = 3v c l =35pf, r l =300 ? t a =+25c t a =-40c to+85c 5 8 ns turn-off time t off(en) v dd = +3v, v no = 2v c l =35pf, r l =300 ? t a =+25c t a =-40c to+85c 6 10 ns v dd = +5v, v no = 3v c l =35pf, r l =300 ? t a =+25c t a =-40c to+85c 1 7 ns break-before- make interval t open v dd = +3v, v no = 2v c l =35pf, r l =300 ? t a =+25c t a =-40c to+85c 1 7 ns logic input cap. c in f = 1mhz t a =+25c, f = 1mhz 8 pf no-off, nc-off-ch cap. c no(off) f = 1mhz; v en =v no =0v t a =+25c, f = 1mhz 8 pf com-on-ch cap c com(on) v en = +2.4v; v com = 0v t a =+25c, f = 1mhz 32 pf preliminary specification - subject to change without notice preliminary specification - subject to change without notice test circuits / timing diagrams figure 1. switching time figure 2. break-before-make interval nc 50 in gnd com aam3202/03 no v dd v dd 300 35pf v com v com v in 50% 50% 90% 90% t r = t f <5ns logic input switch output 0v 0v t on t off v ih v no v in v no nc 50 in gnd com aam3202/03 no v dd v dd 300 35pf v com v com v in 50% 50% 90% 90% t r = t f <5ns logic input switch output 0v 0v t on t off v ih v no v in v no in 50 no, nc gnd com aam3202/03 v dd v dd 300 35pf v com v com v in 50% 90% t r = t f <5ns logic input mux output 0v 0v t open v ih v dd v no 90% v in in 50 no, nc gnd com aam3202/03 v dd v dd 300 35pf v com v com v in 50% 90% t r = t f <5ns logic input mux output 0v 0v t open v ih v dd v no 90% v in
? andigilog, inc. 2004 www.andigilog.com february 2004 ? 70a04011 aam3202 / AAM3203 truth table - aam3202 or AAM3203 in1 com1 connection in2 com2 connection 0 nc1 0 nc2 1 no1 1 no2 - 4 - preliminary specification - subject to change without notice preliminary specification - subject to change without notice packaging information this qfn package is lead-free. 3.000 0.050 3.000 0.050 pin 1 dot marking slp / qfn 10l (3mm x 3mm) top view bottom view 0.500 bsc pin 1 identification r 0.200 typ 0.900 0.050 0.000 - 0.050 side view 2.400 0.050 exposed pad 2.000 ref 0.250 0.050 0.250 0.050 1.700 0.050 exposed pad 0.203 0.025 3.000 0.050 3.000 0.050 pin 1 dot marking slp / qfn 10l (3mm x 3mm) top view bottom view 0.500 bsc pin 1 identification r 0.200 typ 0.900 0.050 0.000 - 0.050 side view 2.400 0.050 exposed pad 2.000 ref 0.250 0.050 0.250 0.050 1.700 0.050 exposed pad 0.203 0.025 tape & reel dimensions ?1.50 min ? 1.50 + 0.10 5.50 0.05 4.00 (note 1.) 12.00 0.30 3.3 0.10 1.1 0.3 0.05 sec - aa 1.75 0.10 part orientation 2.00 0.05 (note 2.) 3.30 3.30 a notes: 1. 10 hole cumulative tol. 0.2 2. measured to the true position of the pocket 8.00 0.10 a ?1.50 min ? 1.50 + 0.10 5.50 0.05 4.00 (note 1.) 12.00 0.30 3.3 0.10 1.1 0.3 0.05 sec - aa 1.75 0.10 part orientation 2.00 0.05 (note 2.) 3.30 3.30 8.00 0.10 a a notes: 1. 10 hole cumulative tol. 0.2 2. measured to the true position of the pocket
life support policy andigilog's products are not authorized for use as critical components in life support devices or systems without the express written approval of the president and general counsel of andigilog, inc. as used herein: 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in th e labeling, can be reasonably expected to result in a significant injury to the user. 2. a critical component is any component of a life support devic e or system whose failure to perform can be reasonably expecte d to cause the failure of the life support device or sy stem, or to affect its safety or effectiveness. andigilog, inc. 8380 s. kyrene rd., suite 101 tempe, arizona 85284-2120 tel: (480) 940-6200 fax: (480) 940-4255 - 5 - ? andigilog, inc. 2004 www.andigilog.com february 2004 ? 70a04013 aam3202 / AAM3203 preliminary specification - subject to change without notice preliminary specification - subject to change without notice data sheet classifications preliminary specification this classification is shown on the heading of each page of a specification for produc ts that are either under development (design and qualification), or in the formative planning stages. andigilog reserves the right to change or discontinue these products without notice. new release specification this classification is shown on the heading of the first page only of a specification for products that are either under the later stages of development (characterization an d qualification), or in the early weeks of release to production. andigilog reserves the right to change the specification and information for these products without notice. fully released specification fully released datasheets do not contain any classifica tion in the first page header. these documents contain specification on products that are in full production. andigilog will not change any guaranteed limits without written notice to the customers. obsolete datasheets that were written prior to january 1, 2001 without any header classification information should be considered as ob solete and non-active specifications, or in the best case as preliminary specifications.
|
